Roadside repairs

The following pages are intended to help in dealing with common roadside emergencies and breakdowns. You will find more detailed fault finding information at the back of the manual, and repair information in the main chapters.

If your car won’t start and the starter motor doesn’t turn

• If it’s a model with automatic transmission, make sure the selector is in ‘P’ or ‘N’.
• Open the bonnet and make sure that the battery terminals are clean and tight.
• Switch on the headlights and try to start the engine. If the headlights go very dim when you’re trying to start, the battery is probably flat. Get out of trouble by jump starting (see next page) using a friend’s car.

If your car won’t start even though the starter motor turns as normal

• Is there fuel in the tank?

Install electrical kit
1. Disconnect negative terminal of battery.
2. If neccessary remove the following covers and panelling:
• In the boot
- Boot floor cover
- Loading lip cover
- Panelling on the left hand side of the boot
• On the righthand side of the vehicle
- Seats of the rear bench seat
- Door sill trim plates.
- Right panelling by the steering column
- Fuse box cover
3. Remove cover from the 40 mm hole in the vehicle tail end panel on the left of centre Fig. 1/5).
4. Fix trailer connection unit in the space provided on the left-hand side of the boot using the fixing screws and M6 nuts provided (Fig. 1/4)
5. Route the end of the cable with the 16-pin plug and eye ring from outside through the hole to the trailer connection unit (Fig. 1/4).
6. Insert the rubber grommet in the hole (Fig. 1/5).
7. Route the end of the cable set with the socket to the socket mounting plate (Fig. 1/6).
8. Push contact insert into the socket housing and slide rubber seal up to the socket.
9. Secure the socket to the mounting plate with the screws provided (Fig. 1/6), torque setting:
max. 2.0 Nm.
10. Locate the 16-way socket housing in the socket provided on the trailer connection unit
(Fig. 1/4).
11. Locate the 12-way socket housing of the 8-core cable set in the socket provided on the trailer
connection unit.
12. The “charge line” and “ground for charge line” functions can be retrofitted via the 3-pin plug
for the permanent positive pre-installation.

Package includes:
1 Socket cable set, 12-core with pre-assembled socket
1 8-core cable set for connection to the on-board electrical system
1 Cable set, 3-core for connection to the power supply
1 Trailer connection unit
1 13-pin socket incl. fitting material
3 Flat pin fuses 15 A
1 Cable ties 300 mm long
15 Cable ties 150 mm long

General procedure:
• Install electrical kit
• Fit socket
• Connect trailer connection unit
• Check operation

Note
When fitting, pay particular attention to the following points:
• Wiring must not be pinched or damaged.
• All seals must be properly seated.
• The seal for the socket must be positioned on the insulating sleeve and not on the individual wires.
• Route wiring so that it does not chaff against the vehicle or break off.
• Do not route wiring immediately next to the exhaust system.

FRONT SEATS

Front manual seat adjustment

Forward and backward:
Pull the lever*1 up and hold it while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position.

Reclining:
To recline the seatback, pull the lever*2 up and lean back. To bring the seatback forward, pull the lever up and lean your body forward. Release the lever to lock the seatback in position.

The reclining feature allows adjustment of the seatback for occupants of different sizes for added comfort and to help obtain proper seat belt fit. (See “PRECAUTIONS ON SEAT BELT USAGE” later in this section.) Also, the seatback can be reclined to allow occupants to rest when the vehicle is stopped and the transmission in the P (Park) position.

Seat lifter (if so equipped):
Pull up or push down the adjusting lever to adjust the seat height until the desired position is achieved.

Why invest in the car wash industry?

Owning a car wash can be a profitable investment for several factors. Here are a few reasons many invest in a car wash:

• Relative autonomy – At a self-serve or automatic car wash, either the customer or equipment performs the labor, thereby eliminating the need for many employees. Generally, it only takes one or two workers to maintain and clean a site throughout busier parts of the day to keep the operation running smoothly.
• Easy to manage – from an operator’s standpoint, a car wash is relatively easy to run in that there are few personnel issues, minimal product inventories, and few maintenance requirements. Additionally, cash flow is not a problem in that there are no accounts receivable or personal checks.
• Low cost – A car wash has low direct operating costs, and fixed costs, such as insurance and bookkeeping, are minimal.

WHY NISSAN SERVICE?

To preserve the quality, reliability and safety of your vehicle, an authorized Nissan dealer is recommended for maintenance or repair. Only an authorized Nissan dealer offers you these advantages:

• Nissan trained and ASE certified technicians
• Immediate access to warranty service history and Nissan technical information
• Latest diagnostic, special tools and service techniques
• Genuine Nissan Parts that meet Nissan’s demanding standards
• 12 month/12,000 mile parts and labor limited warranty when Genuine Nissan Parts are installed by your dealer
• Lifetime limited warranty on select replacement parts
• Complimentary Multi-Point Inspections (at participating dealers)
• Clear, up-front estimates
• Time guaranteed Express Services (at participating dealers)
• Over 1,000 locations nationwide
• Shuttle service/Courtesy van (at participating dealers)

Your Nissan dealer is a full-service maintenance and repair center. We recommend using authorized Nissan Service and genuine Nissan Parts that we have designed for their reliability, safety and suitability for your Nissan vehicle. We are committed to providing you with quick, efficient, and competitively priced service and parts.