Features
Adjustable impeller relief valve

• Allows operator to fine tune impeller performance for wet/heavy or light snow.
• Allows consistent throwing distance in auger stalling conditions.
• Quick recovery time from auger stall condition.

In line impeller

• Only draws in as much snow as it can throw, providing the appropriate balance of speed and torque to maximise capacity and throwing distance.

Reversible auger and impeller

• Allows operator to expel obstructions without exiting machine.

Smooth chute design

• Non metallic liner to prevent freezing up and blocking Deep chute produces smoother, more controlled stream of snow. Design eliminates ledges to prevent bridging and blocking.

Right-click here to download PDF version

ALWAYS

• Perform pre-trip inspection of chutes and augers to insure proper alignment and operation.
• Always carry a personal rescue beacon in areas where avalanche is a danger; assure that the loader is equipped with the proper avalanche rescue kit.
• Be prepared to encounter hidden objects that may clog your machine or become an ejected hazard.
• Maintain two-way radio communication in hazardous areas.

NEVER

• Leave equipment running when operator is not on seat.
• Operate blower in areas where personnel or others are present or allow mechanic work to be done while augers are in motion.
• Operate blower attachment without proper training and preventive maintenance procedures.

PERSONAL PROTECTIVE EQUIPMENT

• Avalanche rescue kit
• CDOT issued orange hard hat
• Cold weather clothing
• Coveralls
• Hearing protection
• Rescue beacon

POTENTIAL HAZARDS

• Avalanche
• Hidden obstacles
• Slips, trips and falls

1 . 1 INTRODUCTION

Thank you for purchasing the PreSonus FIREBOX. PreSonus Audio Electronics has designed the FIREBOX utilizing high-grade components to insure optimum performance that will last a lifetime. The FIREBOX is the most powerful recording interface of its size, with the ability to record and playback six inputs and eight outputs simultaneously at 24-bit/96K sample rate. Loaded with four analog inputs, including two PreSonus microphone preamplifiers and two line inputs, six balanced analog outputs, SPDIF I/O, MIDI I/O, and Cubase LE 48-track recording software, the FIREBOX is ready to go out of the box for professional-quality computer recording. For further flexibility, the FIREBOX can be bus-powered by a six-pin FireWire connector or externally powered by the included power supply. The FIREBOX is the perfect computer recording system that gives you the power for professional quality recordings in the palm of your hand.

Step One:
Unplug Your Xbox 360 Powers Source. Place your fingers into the USB ports, and then place your thumb on the bottom of the Xbox 360 console and pull the face plate completely off.

Step Two:
Now, flip the Xbox on its side and take a close look at the holes located on the top and bottom of each side. If you look closely, you can see the gray tabs towards the ends and in the center of the Xbox 360. These gray tabs are what hold the top and bottom pieces on the Xbox 360. To remove the top and bottom gray pieces, you will need a small pointed object as pictured below.

ASSEMBLY
Unpack and remove the whole unit from packaging, and ensure all the parts are present.(See Figure 1)

1. Set the cutting height to the highest setting. This will make it easier to attach the lower handle section
2. Fit the Lower handle onto the two large lugs on the Main Unit. side and then flex the other side of the handle until it fits the opposite lug. (See Figure 2)
3. Assemble the Upper Handle to the Middle Handle. Use 2 sets of the nuts and bolts to secure in place. Make sure that when the Upper Handle is facing up (safety button facing up) If you have incorrectly assembled this part,disconnect and re-assemble in the correct orientation. (See Figure 1)
4. Use 2 sets of the nuts and bolts to assemble the Upper and Middle Handle assembly to the Lower Handle. The nuts should be positioned on the inside of the handle and the bolts on the outside. (See Figure 4)

Assembly
Remove the lawnmower from carton.

1. Carefully read and understand all instructions before attempting to assemble mower.
2. Assemble the lower handle on to the deck and insert the coach bolt (F) from the inside out into the square hole and handle. Attach the plastic knob and tighten (E) see diagram.
   Note: There are 2 positions in which you can secure the lower handle, choose the one relevant for the user’s comfort.
3. Affix the upper handle using coach bolt. Attach the plastic knob and tighten.
4. Disconnect the spark plug cap (C) see diagram.
5. Engage the safety stop lever (A) by pushing towards the handlebar. Extend the starter cord to retainer (B) in upper handle.
6. Attach a cable tie around the throttle and blade brake cables (D).